Victron Cerbo GX, good AC/DC power monitoring gets better

Ben Ellison

Ben Ellison

Panbo editor, publisher & chief bottlewasher from 4/2005 until 8/2018, and now pleased to have Ben Stein as a very able publisher, webmaster, and editing colleague. Please don't regard him as an "expert"; he's getting quite old and thinks that "fadiddling fumble-putz" is a more accurate description.

50 Responses

  1. Ben Stein Ben Stein says:

    The installation simplicity of the new SmartShunt shouldn’t be overlooked. All it takes is getting the shunt between the first negative distribution and the battery and then connecting a source of 12v positive (probably the battery the shunt is going to be right next to) and you’re off. From there, fire up VictronConnect and configure the shunt. As Ben said, at that point you’ve got a fully functioning battery monitoring system and the option to connect it a myriad of display and management products from Victron.

  2. Victron has been doing everything right for the last few years – adding more and more connectivity options, devices that people need, and ways to combine and configure them that does not take a PhD. I love the direction they’re going with componentized bits that you can combine together as you want to make a full system.

    I have a nice Victron system on my boat, and have been testing the CCGX to NMEA 2000 feature for a bit. This has been a long time coming, and it only reports battery info right now, which is a bit limiting given everything else the CCGX sees. I hope this will expand, perhaps with the new products above.

    • Ben Ellison Ben Ellison says:

      I just tried the Venus GX NMEA 2000 output today, and saw in Maretron N2KAnalyzer that it’s identified as coming from two devices, the Venus and also the attached BMV 712. The BMV is putting out house battery info — SoC, Current, Voltage, and Temp — which will be nice to have on the network. It’s also transmitting a Switch Status PGN, which may have to do with its relay status? Meanwhile, the Venus N2K device isn’t putting out any data PGNs, but seems ready to.

      • Are you running the beta firmware? 2.40…?

        • Ben Ellison Ben Ellison says:

          Yes, I’m pretty sure the latest, but can’t check remotely now because I shut everything down. Sounds Charger/Inverter info is coming soon (at least to the beta):

          “Add NMEA2000 out function: transmit battery monitor out on the VE.Can/NMEA2000 network so it can be picked up by Marine MFDs. Currently it only transmits battery monitor data. Inverter/charger data will follow soon.”

          • Yes I saw that a couple of days ago on the Victron forums. Having the battery information is helpful, although I can get most of that through the Venus+SignalK plugin and then having SignalK spit it out onto NMEA 2000, but that is not native and requires more pieces. I always like simplified things.

            Really looking forward to the inverter/charger data, though!

  3. Keith Pleas says:

    Last line on the METS list of bullets: “Works with most MDF brands”. Ouch.

  4. Ben Ellison Ben Ellison says:

    Cool! NMEA 2000 output is now official in GX update 2.40 and it includes charger/inverter information as well as battery bank monitoring:

    https://www.victronenergy.com/blog/2019/12/11/venus-os-v2-40-nmea2000-out-solar-irradiance-and-more/

    Victron BMV-712 to NMEA 2000 via Venus GX

  5. I had a conversation with a Victron fellow at a recent SSCA Gam, and he alluded to what I think must be the Smartshunt device.

    “My problem is that I have two Link 10s, one for each house bank, and while I am very interested in updating them, I would also rather get rid of the mental arithmetic to add the two together for overall status. If the system can accommodate two such “smartshunts” into a single instrument that can integrate the two inputs, that would be wonderful (especially if it can do it with a Bluetooth port, as I have now with my Victron solar controller)!”

    • Ben Ellison Ben Ellison says:

      I’d really like to see Victron GX supporting multiple shunts, but I’m not sure that’s the intention with their SmartShunts. Also, I think that the Bluetooth will be strictly app to shunt, and mainly for configuration, while the V.E. Direct port will connect to a GX device (like the “Smart” solar controllers).

      Meanwhile, the Simarine Pico can already handle many shunts though they have stopped talking about the NMEA 2000 integration that was supposed to come out in late 2017.

      https://panbo.com/simarine-pico-good-ideas-in-battery-monitoring-more/

      • David A says:

        Agreed; I had all but decided on the Simarine Pico for my main RV monitoring (battery and charging status, tanks) with Victron on the power side (inverter/charger/MPPT) until I saw the Cerbo GX and GX Touch 50. The Cerbo GX/GX Touch 50 seems SO CLOSE to the holy grail; yet without discrete load monitoring, it gives up something to the Simarine.

        I wonder if Victron have any interest in energy monitoring a la Sense, or at least with major loads like A/C, refrigerator, etc.

  6. jan-kees says:

    The BIG advantage of these management devices are the digital inputs. I have connected them to my bilge pumps, and now I get an email from the Victron VRM site when any of them are being used. And it is FREE, it saved me the monthly fees all these other monitoring systems charge. It paid for the Venus in a year !!

  7. Ben Ellison Ben Ellison says:

    I like to think that it makes great sense for the Cerbo GX and the GX Touch 50 to be awarded a Pittman…

    https://www.sailmagazine.com/gear/sail-magazine-2020-pittman-innovation-awards

    … and am also happy to report that preorders will start soon with shipping expected in late March.

  8. Ben Ellison Ben Ellison says:

    Great to see that Cerbo is now officially released, manual included:

    https://www.victronenergy.com/panel-systems-remote-monitoring/cerbo-gx#downloads

    And very nice that the Victron Blog entry about it makes good use of Panbo 😉

    https://www.victronenergy.com/blog/2020/02/06/cerbo-gx-now-on-e-order-and-ready-for-pre-order/

  9. matthew-s says:

    Any indication on timing and price of the SmartShunt? I am doing a complete refit of my electrical and would like to use the SmartShunt and Cerbo GX with the touch to replace the BMV-712.

  10. jan-kees says:

    Call Peter Kennedy..he can tell you 1 410 280 2267

    Or call Justin the US Manager. 1 207 3540493

  11. Ben Ellison Ben Ellison says:

    Very cool! My free VRM monitoring site opened up this morning with a much improved power data dashboard presentation. You can see it too…

    https://vrm.victronenergy.com/installation/30059/share/d9560ba7

    … and, yes, Gizmo refrigeration and gadget loads are outpacing the solar panels, but I’m getting underway soon and a big burst of engine alternator power should show by this evening (though that’s the one major component VRM can’t specifically identify).

  12. Can any of you folks who have a Cerbo tell me how much power it draws? The manual just tells me it has a 3 amp fuse :). If I get one, it will need to be on 24/7, and those amps add up.

    • Howard says:

      I don’t have one but from the GX comparison table in the Victron GX product range document:
      Cerbo GX power draw without GX Touch mounted: around 2.8W. With GX Touch 50 connected, and backlight off: 3.8W. Backlight at max intensity: 4.8W

  13. Ben Stein Ben Stein says:

    I’ve got one but it’s not with me. I seem to recall it draws a touch more than Howard mentioned per Victron’s specs. But, that was measured using a BMV and at that low of power consumption, I’m not sure the accuracy is too high. When I get back to Ft. Myers I’ll put it on a power meter and let you know exactly what I see.

    -Ben S.

  14. Ben and Jan, Thanks! The two fellows on that page who measured theirs were both running a cell device, so their numbers would be higher than what I’m planning on.
    My concern is overnight with me aboard – no cell attachment or other fancy stuffe 🙂

  15. Cam Stevens says:

    I am curious if anyone has run out of the VE Direct ports and whether there is an alternative. I have 3 MPPT 100/30 units (3 solar arrays), the Smart Shunt, and just bought a Victron MultiPlus II. My goal is to wire up all 3 solar arrays as well as the smart shunt, but I will not have enough ports. Is there another port I should use? Ultimately, once fully integrated I hope to have all tanks monitors, bilge alarms and the Inverter/Charger.

    • Ben Stein Ben Stein says:

      Cam,

      I wondered about the same thing. I have a bunch of the USB to VE.Direct cables on hand because I use them with Raspberry Pis. A while ago I tried using one of those with a Cerbo to see if one could expand the VE.Direct connectivity that way. Good news, it works! There are only two USB ports on a Cerbo GX that are general purpose, but I think you could use a USB hub to expand past that limit. I’m not sure if there’s a software limit about how many USB VE.Direct cables are supported, but I also think there’s likely to be a limit at some point as to how many we will really need.

      -Ben S.

    • jan-kees says:

      yes I have ve.direct to USB…then a bunch 5 in a USB hub then a long long long usb cable to the Venus and to the Gerbo..works like a charm
      As input for the Gerbo/Venus I use a small relay which is triggered by the 24V for the bilge pump and the output makes a connection the ground pin of the digital input..so have 5 digital inputs there

      Now Victron is also slowly moving forward with a 2nd OS for the Gerbo/Venus. which integrates with Signal K and with Node RED, creating many many options to integrate.

      I do have to compliment Victron, they are the ONLY one making their management system online available fro free. Think the savings you get for JUST the bilge alerts!

  16. Christopher says:

    Cerbo GX Max. VE.Direct devices /USB 15

  17. William Deertz says:

    I recently installed a Cerbo GX partially based on this review. I’m loving all the data that is reported. I’d like to connect my 24v bilge pumps to the Digital inputs but the Cerbo manual isn’t too clear on how these should be connected. I’ve searched the web but haven’t come up with anything. Can anyone share how they’ve wired their bilge pumps to the Cerbo?

  18. jan-kees says:

    William

    A long time ago I also went the opt coupler way, and even had a small unit deigned to so so…but….
    the digital inputs also work if you just connect them to grand ( the 5th pin)
    so an easy solution is to get a din-rail relay..which can be 12 or 24 V connected to what you want to monitor and the output you connect to one of the digital pins and the ground..

    I have them for my ‘automatic’ whale bilge pumps. the ones with the 3 wires. ( + – and test)
    when the bilge turns on the test wire becomes also positive…so you connect that to the relay and the other to the boats ground…then when the Blige pump turns on, the relay will be closed
    and that connects on of the digital inputs to ground. and voila ..a FREE world wide alert system. That feature alone pays for the Gerbo. 🙂

    • Ben Ellison Ben Ellison says:

      Thanks, Jan-Kees, but can you please explain a little more. I see that each Digital Input has a Plus and Minus pin. Are you saying that a connection between a Minus pin and boat/Cerbo ground activates the input, no Plus voltage needed?

  19. jan-kees says:

    Ben

    YES

    I started with a Venus…and there you only have one minus, so I had to jerry-rig 5 (minus) wires into one.
    Luckily with the Gerbo that pain is removed…

    so just grab a small wire. screw it in the Plus ….enable the alarm..and while looking on the display ….touch the minus with the other end of the wire…and you see….alert 🙂

    Now I use din rail relais Wago 788-304 ( the 24V version)

    so one one side I have the bilge alert (A1 = + A2 = -). and on the relais side I connect 11 to the plus and 14 to the minus. So when the bilge pump goes on…11 and 14 make contact and alert me..thousands of miles away from my boat. Thanks to the free VRM. I do sound like a broken record, but these alerts are paying for the Venus or Gerbo in a year !

  20. jan-kees says:

    you have my email…you can always call me 🙂

  21. William Deertz says:

    Jan-Kees, thanks very much for the input. I’ll be ordering the relays and connecting. As said the Cerbo is well worth the cost considering the versatility.

  22. Jan-Kees, I installed the relay and the bilge pumps are being monitored. I’ve set an alarm to notify me if the pumps stay on for 60 consecutive seconds as this indicates an air lock or a flooding issue. I’d also like to set an alarm if the bilge cycles more than 15 times in a 24 hour period, however, the Victron cycle count is cumulative and doesn’t zero out once per day. Do you know a way to zero out the cycle count parameter?

  23. jan-kees says:

    NO not at this moment….
    The only way to reset the cycle count is to change that digital input to some other setting and then restore it.

    Here is a method where a person added a reset button, and you wil have to add the code to do so every 24 hrs. but it is not standard.
    https://community.victronenergy.com/questions/70207/digital-input-count-clearreset-in-vrm-summary-page.html

    Most likely it could happen in the future when more of the NODE RED will become available with the Venus OS Large
    https://www.victronenergy.com/live/venus-os:large

    I had it installed but have not had enough time to play with it, but it opens up a lot more options to automate and control other things.

  24. Jan-Kees, ok thanks, yes I saw that posting on the Victron forum but figured that wasn’t a good option as it’s unlikely I’ll remember to reset daily. Hopefully Victron will add this ability in a future firmware update. For the time being I’m trying to configure grafana to give me the “first” and “last” data point in a time series so I can monitor the bilge cycle counts in a given time period but having difficulty getting it configured properly. If Victron builds in the reset it would make alarming much easier.

  1. February 6, 2020

    […] Victron Cerbo GX, good AC/DC power monitoring gets better […]

  2. February 8, 2020

    […] Victron Cerbo GX, good AC/DC power monitoring gets better. […]

Join the conversation

Your email address will not be published. Required fields are marked *